Molds tend to grow at homes and affect the general health of those living in it as well as affect the appearance of the house. However one needs to be sure that molds are actually affecting the house. These can be easily done through using Mold Testing Illinois kits. The article below explains some of the types and how they are used.
There are various types of the kits. The first type is known as the lift tape set. This is mainly used when one wants to confirm the exact type of molds. The kits are usually a sticky surface covered by a tacky surface which is removed and the sticky surface placed on the molds then covered again by the tacky surface. The tape is then taken to the lab for testing.
With the instant type kit, the main function is to identify if there are molds in the house. It consists of three elements, a swab, color chart and test tube. The test tube contains the swab which is rubbed over a surface that one thinks it has molds then is put in a test tube. The changes in color of the liquid the tube are then checked after ten minutes and compared to those on the chart to make a conclusion.
The next kit known as the viable kit tests both the presence and exact type of the molds. In the kit, there is a petri dish that contains a gel like substance and a swab. The swab is rubbed over the molds similar to when using the instant kits but then it is also rubbed on the gel. The petri dish is then closed and kept in that condition for 3 to 7days to allow the molds to grow if any.
Other than testing for molds, the viable kits are also used to test the quality of air in a house. This is achieved through using two kits which will have one of the petri dishes placed inside the house in one of the rooms and another placed outside the house but as close as possible to the room in which the other dish is placed. The dishes are opened for an hour then closed for 7days. The results should be similar; if not laboratory testing is necessary.
The same kit can also be used to check the heating and cooling system of the home. To do this, all the vents should be closed except the one that is far away from the system. The kit is placed on the vent that is left open; the system is then switched on to maximum setting. Allow the system to run in this setting for ten minutes then remove the dish. Close it and check it after 7 days for molds growth.
It is important for each of these tests to involve a professional especially in checking the exact kind of molds that are being tested. The laboratories will easily identify these factors. It is important to know the kind of molds as some should not be removed by anyone as they are poisonous and will thus require experts to take care of them.
Molds have been known to lead to high allergies if left not contained with itchy skin and irritated eyes as a common sign of molds. For other people they tend to worsen their conditions example asthma.
There are various types of the kits. The first type is known as the lift tape set. This is mainly used when one wants to confirm the exact type of molds. The kits are usually a sticky surface covered by a tacky surface which is removed and the sticky surface placed on the molds then covered again by the tacky surface. The tape is then taken to the lab for testing.
With the instant type kit, the main function is to identify if there are molds in the house. It consists of three elements, a swab, color chart and test tube. The test tube contains the swab which is rubbed over a surface that one thinks it has molds then is put in a test tube. The changes in color of the liquid the tube are then checked after ten minutes and compared to those on the chart to make a conclusion.
The next kit known as the viable kit tests both the presence and exact type of the molds. In the kit, there is a petri dish that contains a gel like substance and a swab. The swab is rubbed over the molds similar to when using the instant kits but then it is also rubbed on the gel. The petri dish is then closed and kept in that condition for 3 to 7days to allow the molds to grow if any.
Other than testing for molds, the viable kits are also used to test the quality of air in a house. This is achieved through using two kits which will have one of the petri dishes placed inside the house in one of the rooms and another placed outside the house but as close as possible to the room in which the other dish is placed. The dishes are opened for an hour then closed for 7days. The results should be similar; if not laboratory testing is necessary.
The same kit can also be used to check the heating and cooling system of the home. To do this, all the vents should be closed except the one that is far away from the system. The kit is placed on the vent that is left open; the system is then switched on to maximum setting. Allow the system to run in this setting for ten minutes then remove the dish. Close it and check it after 7 days for molds growth.
It is important for each of these tests to involve a professional especially in checking the exact kind of molds that are being tested. The laboratories will easily identify these factors. It is important to know the kind of molds as some should not be removed by anyone as they are poisonous and will thus require experts to take care of them.
Molds have been known to lead to high allergies if left not contained with itchy skin and irritated eyes as a common sign of molds. For other people they tend to worsen their conditions example asthma.
About the Author:
Find a list of the benefits you get when you use mold testing Illinois services and more info about a reputable service provider at http://www.moldprochicago.com/moldprochicago.com/mold-services today.
No comments:
Post a Comment